So at CES this year, I ran into the folks at Belkin who have taken over Linksys and they tell me that they have the solution to my problem in what is called a “Mesh”.  I will get into how it works in a minute but let me say, my eyes glazed over when they tell me it will solve all my problems. I have heard that way too many times. Today the box arrived.

The Linksys VELOP whole home Wi-Fi. I must say the packaging is impressive and elegant, I mean, whoever designed the packaging should win an award. Flip the lid and you see three white towers that are seven and a half inches high by two and a half inches on each side. The first interesting part about setting it up is that you download the Linksys app from either the Apple App Stor or on Google Play. Not for your home computer.

Setting it up is easy to start. Download the app, plug in your first node and the app finds it. It was rather slow to find it so you need to be patient. Same with connecting to the modem you have and in my case, I needed to power down the Spectrum cable modem because it did not connect to it the first time and of course, depending on your modem, can take a while to power back up. This time, it appears to have connected.  From here, you create your Wi-Fi network name (SSID) and password.  

The rest of the setup is very intuitive as it checks your signal strength as you add devices to other locations. After just setting up two devices, I could easily tell that my signal strength in different parts of my home were already higher. Netgear has a nifty tool for your phone called the Wi-Fi Analyzer to tell you what the signal strength in different locations are and also what Wi-Fi hotspots are close to you. Try it in the airport and you will find a ton of signals.  Once a new node is set up, it checks to let you know that you have good signal strength in that location. It didn’t say but I suspect if it was not good, you could simply unplug it and move it to another location.  I waited over an hour before setting up the final node and the only snag was that the power did not come on when I plugged it in. there is a power switch on the bottom so you can turn it off and back on and there is even a reset switch in case you need to start over with that particular node.

Once you are set to go, it then goes out and downloads the latest firmware, installs it, and restarts the devices.

Of course, the acid test will be when my daughter takes her iPhone and iPads to different rooms to use them. The phone App seems to work quite well and I turned on outage notices so will be interesting and I hope I hear nothing at all. From the analyzer above, it appears that the signal strength everywhere is very high (above 80%) nearly all the time. The other good news is that now I don’t have to keep switching hotspots in my home because of the different signal strengths.

See the Linksys page regarding who home Wi-Fi

One of the beauties of such a system is that it coexists very nicely with what you have. I already had a high speed internet router and connection in my office using hubs and routers and wanted to keep it the same and so fortunately, the modem I have from the cable company had four ports.  If it had been a very simple one port modem, the good news is that the Mesh VELOP unit has two Ethernet connections on the bottom of each node to connect other devices or hubs so if you have a laptop that needs to be direct connected, you can do that as well. The nodes are smart enough to self-designate the one that you plug into the router as the master while the others self-configure them as slave nodes. Another thing I like is that the slave nodes only need a power plug to be active and working. They also look nice so that no matter where you place them, they don’t look out of place.  To me though, the best is the seamless internet access across all the nodes with a single Wi-Fi name or hotspot to look for.

If you need more info and detail, the VELOP system is true Tri-band Wi-Fi. It contains three 802.11ac radios (one at 2.4ghz and two at 5 ghz) so it is self-balancing as well. It also can transmit to two clients at the same time so as I upgrade my Wi-Fi connected devices, they can immediately take advantage of the better performance. Each device having six internal antennas also contributes to that boost in performance. It will also support a guest network if you like again, easily administered from the app. If you are concerned about parental controls, that is also available.

Ok, what to quibble about. The idea of scattering the nodes throughout the house has worked wonderfully to the point that I ended up needing a longer CAT5e cable to go from the modem to Node number 1 because of the ease of placing it somewhere it would do the most good. I have used repeaters in the past that take the same SSID or network name as the router but still would often have sporadic outages to the point of needing to be reset. Having wandered from one end of the house to another with a constant feed is working out very well.